davidanna.blogg.se - Autobot blaster usb

#Autobot blaster usb manual
#Autobot blaster usb android
#Autobot blaster usb password
#Autobot blaster usb Pc
#Autobot blaster usb download

Connected the endpoints of the 2 1/2 inch line and the 3/4 inch line.

Draw a 3/4 inch vertical line 3 1/4 inches starting at 3 inches from the left.

Draw a 2 1/2 inch line 1,5 inch from the bottom starting at 3 inches from the left.

Make a vertical line 3 inches from the left and right border.

Cut the 12x24 plywood to 7x14 for both 1/2 inch and 1/8 inch boards.

Using the left over pieces of the 3x24 boards, cut two smaller boards with the measurements of 1"W x 3" L x 1/2" D.

That would make the measurement 1/2" x 1" x 12".

With the last 3x24 inch board, cut the board to a 1x12 inch board.Use the other two 3x24 boards and cut each board to 14 inches in length.Take one of the 3x24 boards and cut two 6 inch pieces.Attached is the Illustrator file so you save yourself creating one yourself :-) Lumber Measurement of the speaker covers: 2 1/8" L x 2 1/8" W x 1/8" D. I requested 2 birch plywood for durability and 2 acrylic. Used services from I had four of them laser cut and shipped to me for $35. 1 - 1" x 36" x 1" dowel from Home Depot 1 - 12" x 24" x 1/8" Birch Veneer Plywood sheet from Utrecht Art 1 - 12" x 24" x 1/2" Birch Veneer Plywood sheet from Utrecht Art 1 - 1/8" sheet of acrylic For aesthetics Two custom laser cut speaker covers. I purchased them individually at $5.84 in stores. Lumber 4 - 3" x 24" x 1/2" Basswood board from Dick Blick Art Materials Note: they sell them in pkg of 5 online.

#Autobot blaster usb android

Bingo! You can now disconnect the USB keyboard and use your Android / iOS device.Īfter configuring the Raspberry Pi, it's now time to build the housing unit to hold the parts together. Press on the arrow keys on your DEVICE and you should see the selection move. Look at the Screen where you've connected the Raspberry Pi. You should now see Use as Remote Control feature.Leave EventServer Port with the default number.

#Autobot blaster usb password

Remember the Username and password you created before in the Raspberry Pi Web Server configuration? Enter that in their respective fields.The HTTP API port matches the same Port number in the Raspberry Pi Web Server configuration.Look for your wireless network, It should display the current IP address. If you used Beginner setup, just navigate to System -> OpenELEC -> Connections. Refer to the Network configuration section from the previous step. Enter the IP address of the Raspberry Pi.If there's no menu option, hit the menu option on your phone to bring up the list of choices.Open the application where is should bring you to the XBMC Hosts.

#Autobot blaster usb download

On an Android / iOS device, download the Official XBMC Remote.

Now it's time to configure the XBMC Remote Control so that you don't have to rely on a USB keyboard to navigate. Proceed to the Remote Control configuration

You can leave the default Username or change it.

Please enable Allow control of XBMC via HTTP.

Like the PC, log into the router, find the DHCP server range and pick one outside the range.

1 and the first three numbers should match the first three numbers of eth0 / eth1.

Look up the ip address for either eth0 (wired) / eth1 (wireless) and Subnet Mask.

Open up the Terminal and enter ifconfig.

Check the DHCP range and select an IP address that is OUTSIDE of the range for your Raspberry Pi.

Log into your router and navigate to the section where it mentions about DHCP server.

The Default Gateway is your Wireless Router.

Make a note of the Subnet Mask and Default Gateway.

Open up the Command Prompt and enter ipconfig /all.

#Autobot blaster usb Pc

Find your your current Network Settings on a PC / Mac.

#Autobot blaster usb manual

Select the IPv4 tab and change the IP Address Method to Manual.

Select your wireless network and select Edit.

This is to easily recognize the Raspberry Pi by IP address.

You need to change the type of IP addressing from DHCP to Manual.

Follow Steps 1 through 4 for Beginners.

For a list of all compatible Wi-Fi devices, please visit. If nothing shows up, please check the USB Wifi Adapter and see if it's compatible with the Raspberry Pi.

A list of wireless networks should show up including yours.

Enter any security pass phrases if any and you should be connected to the wireless. Select your wireless network and hit connect. Network Configuration: Setup (Beginners): The next step after the layout is to configure the network settings and web server services (for remote control with Android / iOS).